Domotique/WiFiAccessPointConfigurator/WiFiAccessPointConfigurator.ino

/* Generic GPIO Control by HTTP REST interface                     */
/* Modify GPIO by accessing DEVICE_IP/gpio?gpio=[GPIO]&value=[0|1] */
/* At first boot it creates a WiFi access point                    */
/*  and provide a web server on it, so you can configure Wifi ssid */
/*  Wifi passwd, and a mDNS hostname                               */
/* In this mode, device will be available at 192.168.4.1           */
/* Device can also be put in OTA Mode: In this case, if you have   */
/*  a little flash (512K), it better to disable SPIFFS in          */
/*  "Flash Size" Menu. Use espota.py to upload OTA                 */
/* After passing in OTA mode, next boot will be in setup mode      */

/* To Use GPIO 3 And 1, uncomment #define ENABLE_EXTRA_GPIO        */
/*  but Serial will be available on GPIO 15 and 13                 */

#include <ESP8266WiFi.h>
#include <WiFiClient.h>
#include <ESP8266WebServer.h>
#include <ESP8266mDNS.h>
#include <EEPROM.h>
#include <ArduinoOTA.h>
#include <errno.h>

//#define ENABLE_EXTRA_GPIO

#define EEPROM_SIZE 512

char eeprom[EEPROM_SIZE];

#define BOOTMODE_SETUP  0
#define BOOTMODE_NORMAL 1
#define BOOTMODE_OTA    2

int mode;

/* Set these to your desired credentials. */
const char *ssid = "ESPConfigurator";

ESP8266WebServer server(80);

/* WebServer decl*/
void handleRoot();
void handleSetup();
void handleGpio();
void handleSave();
void handleOTA();
void handleNotFound();
void setupWebServer(int bootmode);

/* EEPROM decl */
int saveConfig(int bootMode, String ssid, String password, String host );
int saveBootMode(int bootMode);
void readEEPROM(int &bootMode, char **ssid, char **password, char **host);

void setupWifi(int bootmode, int forceSetup, char *confSsid, char *confPassword, char *confHost) {
  IPAddress myIP;
  if (bootmode == BOOTMODE_SETUP || forceSetup) {
    Serial.println("Configuring access point...");
    /* You can set a password to the AP here */
    WiFi.softAP(ssid);
    myIP = WiFi.softAPIP();
  } else {
    Serial.println("Connecting to Wifi...");
    WiFi.begin(confSsid, confPassword);
    while (WiFi.status() != WL_CONNECTED) {
      delay(500);
      Serial.print(".");
    }
    Serial.println("");
    Serial.println("WiFi connected");

    if (!MDNS.begin(confHost)) {
      Serial.println("Error setting up MDNS responder!");
      while (1) {
        delay(1000);
      }
    }
    Serial.println("mDNS responder started");
    myIP = WiFi.localIP();
  }

  Serial.print("My IP address: ");
  Serial.println(myIP);
}

void setupOTA() {
  // Port defaults to 8266
  // ArduinoOTA.setPort(8266);

  // Hostname defaults to esp8266-[ChipID]
  // ArduinoOTA.setHostname("myesp8266");

  // No authentication by default
  // ArduinoOTA.setPassword((const char *)"123");

  //Disable OTA mode to avoid forever loop
  //Force BOOTMODE_SETUP in case eeprom layout have changed
  saveConfig(BOOTMODE_SETUP, "", "", "" );

  ArduinoOTA.onStart([]() {
    Serial.println("Start");
  });
  ArduinoOTA.onEnd([]() {
    Serial.println("\nEnd");
  });
  ArduinoOTA.onProgress([](unsigned int progress, unsigned int total) {
    Serial.printf("Progress: %u%%\r", (progress / (total / 100)));
  });
  ArduinoOTA.onError([](ota_error_t error) {
    Serial.printf("Error[%u]: ", error);
    if (error == OTA_AUTH_ERROR) Serial.println("Auth Failed");
    else if (error == OTA_BEGIN_ERROR) Serial.println("Begin Failed");
    else if (error == OTA_CONNECT_ERROR) Serial.println("Connect Failed");
    else if (error == OTA_RECEIVE_ERROR) Serial.println("Receive Failed");
    else if (error == OTA_END_ERROR) Serial.println("End Failed");
  });
  ArduinoOTA.begin();
  Serial.println("Ready");
  Serial.print("IP address: ");
  Serial.println(WiFi.localIP());
  Serial.print("Free Space: ");
  Serial.println(ESP.getFreeSketchSpace());
}

void setup() {
  pinMode(3, OUTPUT);

  char *confSsid;
  char *confPassword;
  char *confHost;

  delay(1000);
  Serial.begin(115200);
  Serial.println();

  // Get GPIO 3 Status
  Serial.swap(); //Switch Serial on GPIO 13 & 15
  pinMode(3, INPUT_PULLUP);
  int txStatus = digitalRead(3);
#ifndef ENABLE_EXTRA_GPIO
  Serial.swap(); // Switch back on GPIO 1 & 3
#endif

  EEPROM.begin(EEPROM_SIZE);
  readEEPROM(mode, &confSsid, &confPassword, &confHost);
  if (mode == BOOTMODE_NORMAL || mode == BOOTMODE_OTA) {
    Serial.println("Configuration Found !:");
    Serial.println(mode);
    Serial.println(confSsid);
    Serial.println(confPassword);
    Serial.println(confHost);
    Serial.println();
  } else {
    Serial.println("No configuration saved");
  }

  Serial.print("Force Setup Mode ? :");
  Serial.print(txStatus?"No":"Yes");
  Serial.println();

  setupWifi(mode, txStatus == 0, confSsid, confPassword, confHost);

  if (mode == BOOTMODE_OTA) {
    setupOTA();
  } else {
    setupWebServer(mode);
  }
}

void loop() {

  if (mode == BOOTMODE_OTA) {
    ArduinoOTA.handle();
  } else {
    server.handleClient();
  }
}