Adafruit_MQTT_Library/examples/mqtt_winc1500/mqtt_winc1500.ino

157 lines
4.7 KiB
C++

/***************************************************
Adafruit MQTT Library WINC1500 Example
Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!
Written by Limor Fried/Ladyada for Adafruit Industries.
MIT license, all text above must be included in any redistribution
****************************************************/
#include <SPI.h>
#include "Adafruit_MQTT.h"
#include "Adafruit_MQTT_Client.h"
#include <Adafruit_WINC1500.h>
/************************* WiFI Setup *****************************/
#define WINC_CS 8
#define WINC_IRQ 7
#define WINC_RST 4
#define WINC_EN 2 // or, tie EN to VCC
Adafruit_WINC1500 WiFi(WINC_CS, WINC_IRQ, WINC_RST);
char ssid[] = "yournetwork"; // your network SSID (name)
char pass[] = "yourpassword"; // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0; // your network key Index number (needed only for WEP)
int status = WL_IDLE_STATUS;
/************************* Adafruit.io Setup *********************************/
#define AIO_SERVER "io.adafruit.com"
#define AIO_SERVERPORT 1883
#define AIO_USERNAME "adafruitiousername"
#define AIO_KEY "adafruitiokey"
/************ Global State (you don't need to change this!) ******************/
//Set up the wifi client
Adafruit_WINC1500Client client;
Adafruit_MQTT_Client mqtt(&client, AIO_SERVER, AIO_SERVERPORT, AIO_USERNAME, AIO_KEY);
// You don't need to change anything below this line!
#define halt(s) { Serial.println(F( s )); while(1); }
/****************************** Feeds ***************************************/
// Setup a feed called 'photocell' for publishing.
// Notice MQTT paths for AIO follow the form: <username>/feeds/<feedname>
Adafruit_MQTT_Publish photocell = Adafruit_MQTT_Publish(&mqtt, AIO_USERNAME "/feeds/photocell");
// Setup a feed called 'onoff' for subscribing to changes.
Adafruit_MQTT_Subscribe onoffbutton = Adafruit_MQTT_Subscribe(&mqtt, AIO_USERNAME "/feeds/onoff");
/*************************** Sketch Code ************************************/
#define LEDPIN 13
void setup() {
#ifdef WINC_EN
pinMode(WINC_EN, OUTPUT);
digitalWrite(WINC_EN, HIGH);
#endif
while (!Serial);
Serial.begin(115200);
Serial.println(F("Adafruit MQTT demo for WINC1500"));
// Initialise the Client
Serial.print(F("\nInit the WiFi module..."));
// check for the presence of the breakout
if (WiFi.status() == WL_NO_SHIELD) {
Serial.println("WINC1500 not present");
// don't continue:
while (true);
}
Serial.println("ATWINC OK!");
pinMode(LEDPIN, OUTPUT);
mqtt.subscribe(&onoffbutton);
}
uint32_t x=0;
void loop() {
// Ensure the connection to the MQTT server is alive (this will make the first
// connection and automatically reconnect when disconnected). See the MQTT_connect
// function definition further below.
MQTT_connect();
// this is our 'wait for incoming subscription packets' busy subloop
Adafruit_MQTT_Subscribe *subscription;
while ((subscription = mqtt.readSubscription(5000))) {
if (subscription == &onoffbutton) {
Serial.print(F("Got: "));
Serial.println((char *)onoffbutton.lastread);
if (0 == strcmp((char *)onoffbutton.lastread, "OFF")) {
digitalWrite(LEDPIN, LOW);
}
if (0 == strcmp((char *)onoffbutton.lastread, "ON")) {
digitalWrite(LEDPIN, HIGH);
}
}
}
// Now we can publish stuff!
Serial.print(F("\nSending photocell val "));
Serial.print(x);
Serial.print("...");
if (! photocell.publish(x++)) {
Serial.println(F("Failed"));
} else {
Serial.println(F("OK!"));
}
}
// Function to connect and reconnect as necessary to the MQTT server.
// Should be called in the loop function and it will take care if connecting.
void MQTT_connect() {
int8_t ret;
// attempt to connect to Wifi network:
while (WiFi.status() != WL_CONNECTED) {
Serial.print("Attempting to connect to SSID: ");
Serial.println(ssid);
// Connect to WPA/WPA2 network. Change this line if using open or WEP network:
status = WiFi.begin(ssid, pass);
// wait 10 seconds for connection:
uint8_t timeout = 10;
while (timeout && (WiFi.status() != WL_CONNECTED)) {
timeout--;
delay(1000);
}
}
// Stop if already connected.
if (mqtt.connected()) {
return;
}
Serial.print("Connecting to MQTT... ");
while ((ret = mqtt.connect()) != 0) { // connect will return 0 for connected
Serial.println(mqtt.connectErrorString(ret));
Serial.println("Retrying MQTT connection in 5 seconds...");
mqtt.disconnect();
delay(5000); // wait 5 seconds
}
Serial.println("MQTT Connected!");
}