Adafruit_MQTT_Library/examples/mqtt_cc3k/mqtt_cc3k.ino

#include <Adafruit_SleepyDog.h>
#include <Adafruit_CC3000.h>
#include <SPI.h>
#include "utility/debug.h"
#include "Adafruit_MQTT.h"
#include "Adafruit_MQTT_CC3000.h"

/*************************** CC3000 Pins ***********************************/

#define ADAFRUIT_CC3000_IRQ   3  // MUST be an interrupt pin!
#define ADAFRUIT_CC3000_VBAT  5  // VBAT & CS can be any digital pins.
#define ADAFRUIT_CC3000_CS    10
// Use hardware SPI for the remaining pins
// On an UNO, SCK = 13, MISO = 12, and MOSI = 11

// Alternate config:
//#define ADAFRUIT_CC3000_IRQ   2
//#define ADAFRUIT_CC3000_VBAT  8
//#define ADAFRUIT_CC3000_CS    10

/************************* WiFi Access Point *********************************/

#define WLAN_SSID       "...your SSID..."  // can't be longer than 32 characters!
#define WLAN_PASS       "...your password..."
#define WLAN_SECURITY   WLAN_SEC_WPA2  // Can be: WLAN_SEC_UNSEC, WLAN_SEC_WEP, 
                                       //         WLAN_SEC_WPA or WLAN_SEC_WPA2

/************************* Adafruit.io Setup *********************************/

#define AIO_SERVER      "io.adafruit.com"
#define AIO_SERVERPORT  1883
#define AIO_USERNAME    "...your AIO username (see https://accounts.adafruit.com)..."
#define AIO_KEY         "...your AIO key...";

/* Debug server configuration (not normally used):
#define AIO_SERVER      "apt.adafruit.com"
#define AIO_SERVERPORT  1883
*/

/************ Global State (you don't need to change this!) ******************/

// Setup the main CC3000 class, just like a normal CC3000 sketch.
Adafruit_CC3000 cc3000 = Adafruit_CC3000(ADAFRUIT_CC3000_CS, ADAFRUIT_CC3000_IRQ, ADAFRUIT_CC3000_VBAT);

// Store the MQTT server, client ID, username, and password in flash memory.
// This is required for using the Adafruit MQTT library.
const char MQTT_SERVER[] PROGMEM    = AIO_SERVER;
const char MQTT_CLIENTID[] PROGMEM  = AIO_KEY;
const char MQTT_USERNAME[] PROGMEM  = AIO_USERNAME;
const char MQTT_PASSWORD[] PROGMEM  = AIO_KEY;

// Setup the CC3000 MQTT class by passing in the CC3000 class and MQTT server and login details.
Adafruit_MQTT_CC3000 mqtt(&cc3000, MQTT_SERVER, AIO_SERVERPORT, MQTT_CLIENTID, MQTT_USERNAME, MQTT_PASSWORD);

// You don't need to change anything below this line!
#define halt(s) { Serial.println(F( s )); while(1);  }

// CC3000connect is a helper function that sets up the CC3000 and connects to
// the WiFi network. See the cc3000helper.cpp tab above for the source!
boolean CC3000connect(const char* wlan_ssid, const char* wlan_pass, uint8_t wlan_security);

/****************************** Feeds ***************************************/

// Setup a feed called 'photocell' for publishing.  
// Notice MQTT paths for AIO follow the form: <username>/feeds/<feedname>
const char PHOTOCELL_FEED[] PROGMEM = AIO_USERNAME "/feeds/photocell";
Adafruit_MQTT_Publish photocell = Adafruit_MQTT_Publish(&mqtt, PHOTOCELL_FEED);

// Setup a feed called 'onoff' for subscribing to changes.  
const char ONOFF_FEED[] PROGMEM = AIO_USERNAME "/feeds/onoff";
Adafruit_MQTT_Subscribe onoffbutton = Adafruit_MQTT_Subscribe(&mqtt, ONOFF_FEED);

/*************************** Sketch Code ************************************/

void setup() {
  Serial.begin(115200);

  Serial.println(F("Adafruit MQTT demo"));

  Serial.print(F("Free RAM: ")); Serial.println(getFreeRam(), DEC);

  // Initialise the CC3000 module
  Serial.print(F("\nInit the CC3000..."));
  if (!cc3000.begin()) 
      halt("Failed");

  mqtt.subscribe(&onoffbutton);

  while (! CC3000connect(WLAN_SSID, WLAN_PASS, WLAN_SECURITY)) {
    Serial.println(F("Retrying WiFi"));
    while(1);
  }

  Serial.println(F("Connected to WiFi!"));
  //////////////////////////////
  Serial.println(F("Connecting to MQTT..."));
  int8_t ret;
  while ((ret = mqtt.connect()) != 0) {
       switch (ret) {
          case 1: Serial.println(F("Wrong protocol")); break;
          case 2: Serial.println(F("ID rejected")); break;
          case 3: Serial.println(F("Server unavail")); break;
          case 4: Serial.println(F("Bad user/pass")); break;
          case 5: Serial.println(F("Not authed")); break;
          case 6: Serial.println(F("Failed to subscribe")); break;
          default: {
            Serial.println(F("Connection failed")); 
            CC3000connect(WLAN_SSID, WLAN_PASS, WLAN_SECURITY);  // y0w, lets connect to wifi again
            return;           // restart the loop
          }
       }
       Serial.println(F("Retrying MQTT connection"));
       delay(5000); 
  }
  //////////////////////////////

  Serial.println(F("MQTT Connected!"));  
}

uint32_t x=0;

void loop() {
  // Make sure to reset watchdog every loop iteration!
  Watchdog.reset();
 
  // Try to ping the MQTT server
  /*
  if (! mqtt.ping(3) ) {
    // MQTT pings failed, lets reconnect
    Serial.println("Ping fail!");
  }
  */

  // this is our 'wait for incoming subscription packets' busy subloop
  Adafruit_MQTT_Subscribe *subscription;
  while (subscription = mqtt.readSubscription(1000)) {
    if (subscription == &onoffbutton) {
      Serial.print(F("Got: ")); 
      Serial.println((char *)onoffbutton.lastread);
    }
  }
  
  // Now we can publish stuff!
  Serial.print(F("\nSending photocell val ")); 
  Serial.print(x);
  Serial.print("...");
  if (! photocell.publish(x++)) {
    Serial.println(F("Failed"));
  } else {
    Serial.println(F("OK!"));
  }
}